Hobbico Mini Switch Manual de instrucciones

Entire Contents © 2013 Hobbico®, Inc. FLZA3320 RTF FLZA3322 Tx-RREAD THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANTINSTRUCT

10● NEVER discharge below 2.75V per cell.● NEVER place on combustible materials or leave unattended during charge or discharge.● ALWAYS KEEP OUT OF

11❏ 6. When checking the propeller operation, BE SURE TO KEEP YOUR HANDS, CLOTHING, ETC. BEHIND THE SPINNING ARC OF THE PROPELLER! Operate the propel

12 ❏ 2. With the wings attached to the fuselage, all parts of the model installed (ready to fl y) and the battery installed, lift the model with two fi

13● The motor gets hot! Do not touch it during or right after operation. ● Do not throw anything into the propeller of a rotating motor.AMA SAFETY C

14FLYINGCAUTION (THIS APPLIES TO ALL R/C AIRPLANES): If, while fl ying, you notice an alarming or unusual sound such as a low-pitched “buzz,” this may

1520A ESC INSTRUCTIONSSPECIFICATIONSConstant Current: Burst Current (< 10 seconds):BEC Mode:BEC Output: BEC Output Capability: Battery Cell Count:

16(“ 1 2 1 2”) indicating that the value has been set and saved. If you immediately lower the throttle stick (within two seconds) you will exit progra

17TACTIC TTX404 2.4GHZ4-CHANNEL SPREAD SPECTRUM RADIO INSTRUCTIONSThe Tactic TTX404 airplane radio system uses an advanced 2.4GHz spread spectrum tech

18Anytime the LED begins to fl ash, accompanied by the sounding of an audible tone, the Tx battery voltage has dropped too low and operation of the mod

19 ADJUSTABLE STICKSThe length of both gimbal sticks can be adjusted as desired. Loosen the set screw inside the center of the stick with a 2mm hex wr

2INTRODUCTIONThank you for purchasing the Mini Switch! Following the success of the larger, original Switch plane, the Mini Switch gives you two diffe

206. The LED on the teacher’s Tx will fl ash 3 times to indicate it has become bound with the student’s Tx.7. The teacher can then release his traine

21 3. Move the Tx throttle stick to the desired position for the throttle control to move if the Rx goes to failsafe. 4. Press and hold the “Bind” b

22Tactic TR624 ReceiverChannels 6Frequencies2.403 – 2.480 GHzModulationFHSS spread spectrumInput powerFour “AA” alkaline, NiCd or NiMH cells(4.0 – 6.

23FAILSAFE NOT WORKING CORRECTLYReceiver is not properly binded to the transmitter – bind the Rx to the Tx and re-try. Contact Hobby Services for furt

24CE COMPLIANCE INFORMATIONFOR THE EUROPEAN UNIONThe associated regulatory agencies of the following countries recognize the noted certifications for

33. You must take time to build straight, true and strong.4. You must use an R/C radio system that is in fi rst-class condition, and a correctly size

4TOOLS REQUIREDThe Mini Switch requires only a screwdriver to fi nish assembly: ❍ #2 Phillips screw driverKIT INSPECTIONBefore starting to build, take

5ASSEMBLE THE MODELInstall the Tail Section ❏ 1. Slide the horizontal stabilizer between the tail pushrods and the stabilizer pocket. You will need t

6 ❏ 2. Slide the carbon wing joiner through the tube in the high wing canopy hatch and center its position. ❏ 3. Tighten the outer screws on the unde

7 ❏ 7. Test fi t the canopy hatch onto the fuselage by inserting the tongue at the front of the hatch into the pocket in the fuselage and pressing the

8 ❏ 5. You have now completed the assembly of the high wing confi guration of the Mini Switch!CHANGING TO THE LOW WINGCONFIGURATIONOnce you are accus

9 ❏ 6. Connect the Y-harness to the aileron servo leads. Test fi t the low wing confi guration canopy hatch to the fuselage and screw it in place. NOTE